
Conventional Lathe
CA6140 Conventional Lathe
A manual engine lathe for turning shafts, sleeves, flanges and threaded rotational parts. The CA6140 has a 400 mm swing over bed, a 400 mm wide bed guideway and a vertical square tool post. Select the between-centers length and spindle bore for the workpiece before quotation.
Part and Model Fit
Is the CA6140 Right for Your Parts?
Check the blank diameter at the bed, cross slide and removable gap separately. Then confirm length between centers, workpiece weight, spindle bore and the required manual turning or thread-cutting operations.

Shafts and Stepped Shafts
For rotational shafts that fit the selected 750-4,000 mm between-centers length. Long or slender pieces need a workholding and support review before cutting.

Sleeves and Bushings
For outside-diameter, bore, face and groove work on parts that fit the spindle, chuck and 210 mm swing over the cross slide.

Flanges and Short Larger-Diameter Parts
The removable-gap area provides a 630 mm swing for a short section of the workpiece, with a 210 mm gap length. Confirm carriage clearance and the complete machining plan for each drawing.
Good Initial Fit
- Manual turning of one-off, repair or varied small-batch parts.
- Blank fits the 400 mm bed swing and 210 mm cross-slide swing where the carriage must travel.
- Workpiece weight between centers is within the catalogued 300 kg limit, subject to workholding and speed review.
- Required thread type and pitch fall within the selected machine's change-gear and feed setup.
Review Another Configuration
- A larger bore is needed for bar or tube pass-through: confirm the 80(B) mm spindle-bore variant instead of the 52 mm version.
- Part length exceeds the selected between-centers version, or the finished cut cannot clear the carriage and chuck.
- Repeat production requires programmed tool paths, automatic indexing or cycle automation: consider a CNC lathe.
- Thin-walled, eccentric or slender workpieces require a specific chuck, fixture or steady-rest plan.
Send the drawing, blank size, material, weight, operations, thread specification and destination so the correct length and spindle-bore variant can be reviewed.
Submit Your Part DrawingMachine Features
CA6140 Design Advantages
The construction and manual controls below help define where the CA6140 fits. Final cutting conditions and equipment are confirmed for the selected machine and part.
CA6140 bed and guideways photo400 mm Bed Guideway Width
The CA6140 has a 400 mm bed guideway width. This provides the carriage and tailstock with a broad support path for general turning. Actual cutting limits depend on the workpiece, tool, clamping and selected speed and feed.
CA6140 removable gap beside headstock photoRemovable Gap for Short Larger-Diameter Work
The swing over the gap is 630 mm and the gap length is 210 mm. This gives clearance for a short flange or disc section near the headstock. The full part and tool path must still clear the cross slide, chuck and carriage.
CA6140 spindle nose and bore photoTwo Spindle-Bore Variants
A 52 mm spindle bore and an 80(B) mm variant are listed. Choosing the bore against bar or tube diameter can reduce cut-to-length handling when pass-through is practical. Confirm the selected spindle, chuck and usable through-hole before ordering.
CA6140 headstock speed levers and feed controls photoStepped Spindle Speeds and Mechanical Feeds
The CA6140 has 24 forward and 12 reverse spindle-speed steps, plus 64 feed rates. Operators can select a step for part diameter, material and operation. Confirm the exact spindle-speed range for the selected configuration.
CA6140 square tool post and compound slide photoManual Square Tool Post and Compound Slide
A vertical square tool post takes 25 x 25 mm shank tools. The top and compound slide travels are listed as 140 / 320 mm, with a tool-post swivel of plus or minus 90 degrees. This supports manual setup for faces, steps and taper work within the available clearance.
CA6140 tailstock and quill photoTailstock Support for Between-Centers Work
The tailstock has a 75 mm sleeve diameter, 150 mm sleeve travel and a Morse No. 5 sleeve taper. It supports center-held shafts and can carry compatible tailstock tooling. Check the center load, part deflection and any additional support needed for long or slender pieces.
Machine Data
CA6140 Technical Specifications
Capacity
| Parameter | Unit | CA6140 |
|---|---|---|
| Swing over bed | mm | 400 |
| Swing over cross slide | mm | 210 |
| Swing over gap | mm | 630 |
| Removable gap length | mm | 210 |
| Between-centers length choices | mm | 750 / 1,000 / 1,500 / 2,000 / 3,000 / 4,000 |
| Maximum workpiece weight between centers | kg | 300 |
| Bed guideway width | mm | 400 |
Spindle
| Parameter | Unit | CA6140 |
|---|---|---|
| Spindle bore | mm | 52 / 80(B), depending on variant |
| Spindle nose | - | ISO(GB) C6 / D8; confirm by variant |
| Spindle taper | - | Morse No. 6 |
| Forward speed steps | steps | 24 |
| Reverse speed steps | steps | 12 |
| Spindle speed range | r/min | To be confirmed for the selected configuration |
| Main motor power | kW | 7.5 |
Feeds and Threading
| Parameter | Unit | CA6140 |
|---|---|---|
| Number of feed rates | rates | 64 |
| Longitudinal standard feed | mm/rev | 0.08-1.59 |
| Longitudinal fine feed | mm/rev | 0.028-0.054 |
| Longitudinal coarse feed | mm/rev | 1.71-6.33 |
| Cross standard feed | mm/rev | 0.04-0.79 |
| Cross fine feed | mm/rev | 0.014-0.027 |
| Cross coarse feed | mm/rev | 0.86-3.16 |
| Metric threads | mm | 44 types; 1-192 |
| Module threads | module | 39 types; 0.25-48 |
| Imperial threads | TPI | 21 types; 2-24 |
| Diametral-pitch threads | DP | 37 types; 1-96 |
Tool Post and Tailstock
| Parameter | Unit | CA6140 |
|---|---|---|
| Tool post | - | Vertical square tool post |
| Tool shank size | mm | 25 x 25 |
| Top / compound slide travel | mm | 140 / 320 |
| Tool-post swivel | degrees | +/- 90 |
| Tailstock sleeve diameter | mm | 75 |
| Tailstock sleeve travel | mm | 150 |
| Tailstock sleeve taper | - | Morse No. 5 |
Coolant and Electrical
| Parameter | Unit | CA6140 |
|---|---|---|
| Coolant motor power | W | 90 |
| Coolant pump head | m | 5 |
| Coolant pump flow | L/min | 25 |
| Power supply | - | 380 V +/-10%, 50 Hz +/-1 Hz (catalog); destination requirements to confirm |
Between-centers length and spindle bore depend on the selected configuration. Confirm the exact spindle-speed range, overall dimensions and machine weight in the quotation; request the installation drawing for the chosen bed length.
Model Fit
CA6140 Quick Selection Guide
Start with blank diameter, between-centers length and bore. Then check manual operation, threading and support requirements.
| Customer Requirement | Recommended Direction | Reason for Selection | Next Step |
|---|---|---|---|
| Blank diameter ≤400 mm and manual turning is suitable | CA6140 | Check the 210 mm cross-slide swing over the full tool path. | Send the blank and finished-part drawing. |
| Short flange or disc section exceeds 400 mm but is ≤630 mm | CA6140 gap area, subject to review | The removable gap is 210 mm long; only a short section can use the larger swing. | Confirm chuck, carriage and tool clearance. |
| Bar or tube needs to pass through spindle | Choose 52 or 80(B) mm bore | Bore depends on the selected spindle variant. | Provide stock outside diameter and chuck plan. |
| Part length varies by job | Choose 750 / 1,000 / 1,500 / 2,000 / 3,000 / 4,000 mm between centers | The correct bed version follows overall part length and support method. | Provide total length, machining length and weight. |
| Programmed repeat cycles or automatic tool changes are required | Review a CNC lathe | The CA6140 uses manual controls and a square tool post. | Provide cycle target and annual quantity. |
The maximum stated workpiece weight between centers is 300 kg. Safe setup still depends on clamping, support and rotational speed.
Send the drawing, material, maximum diameter, length, weight, thread details, quantity and destination for a configuration review.
Submit Your Part DrawingSelection Comparison
CA6140 Conventional Lathe or CNC Lathe?
The choice turns on production method as much as part size. CA6140 suits manual setup and varied turning work; a CNC model is worth reviewing when programmed cycles and repeated batches are required.
| Comparison Item | CA6140 Conventional Lathe | CNC Lathe to Review |
|---|---|---|
| Primary operation | Manual turning, facing and threading | Programmed turning cycles and repeat machining |
| Tool changing | Operator sets tools in a vertical square tool post | Turret configuration depends on selected model |
| Workpiece length | Choose a 750-4,000 mm between-centers CA6140 version | Choose a CNC model against actual machining length and support plan |
| Spindle bore | 52 or 80(B) mm CA6140 variant | Depends on CNC model and variant |
| Best buying question | Are manual setup and control appropriate for the part mix? | Will programming and repeatability justify CNC setup? |
This is a process-level comparison. A CNC model must be selected by its own verified capacity, workholding and control specification.
Quality Documentation
Company Certificates
Production View
Factory Inventory and Production Line
Add factory image URL
Add production image URL
Add inspection image URL
Add component image URL
Add completed-machine image URL
Add production-line image URLCommon Questions
CA6140 FAQ
What is the maximum swing of the CA6140?
The listed specifications include 400 mm swing over bed, 210 mm swing over cross slide, and 630 mm swing over the removable gap for a 210 mm gap length. Gap swing applies only within the gap area; confirm carriage and tool clearance for the part.
Which between-centers lengths are available?
The manual lists 750, 1,000, 1,500, 2,000, 3,000 and 4,000 mm versions. The suitable version depends on total part length, machining length and support arrangement.
Does the CA6140 have a 52 mm or 80 mm spindle bore?
The catalog lists a 52 mm standard bore and an 80(B) mm variant. Confirm the selected spindle variant and usable through-hole in the quotation.
What spindle speeds are available?
The CA6140 is listed with 24 forward and 12 reverse speed steps. Confirm the exact spindle-speed range for the selected machine before ordering.
Can the CA6140 cut metric and imperial threads?
The catalog lists 44 metric thread types (1-192), 39 module thread types (0.25-48), 21 imperial thread types (2-24 TPI), and 37 diametral-pitch thread types (1-96 DP). Confirm required pitch and setup compatibility before purchase.
What is the maximum workpiece weight?
The catalog lists 300 kg between centers. The safe setup depends on workpiece geometry, center support, chucking, rotational speed and cutting forces.
Is this a CNC lathe?
No. CA6140 is a conventional manual lathe with hand-operated controls and a square tool post. Review a CNC model if programmed cycles or automatic tool indexing are required.
What information is needed for a quotation?
Send the part drawing, blank diameter and length, material, workpiece weight, operations, thread specifications, production quantity, preferred bore, between-centers length, destination and electrical requirements.





